Pure Sound. For Music Lovers.
MADDECKERS

Home / Guides / MG II Bluetooth

MG II use guide

How do I pair or reconnect MG II with Bluetooth?

Turn MG II on, select Bluetooth with the Mode button if needed, then choose MG II in your phone settings. Hold the EQ button for three seconds to start Bluetooth re-pairing.

Short answer

Turn MG II on by holding the power button for three seconds. If Bluetooth is not the active source, use the Mode button to select it, then choose MG II in your phone's Bluetooth settings. The official manual says to hold the EQ button for three seconds to re-pair Bluetooth.

Pair MG II with your phone

  1. Hold the power button for three seconds to turn MG II on.
  2. Press the Mode button if needed until Bluetooth is selected.
  3. On your phone, turn Bluetooth on and select MG II from the available devices. Keep the phone close to the speaker while pairing.
  4. Start audio on the phone and adjust volume on the phone and speaker as needed.

Reconnect or pair with a different phone

  1. Disconnect MG II from any nearby device that may already be connected. If you are moving to a new phone, forget the earlier MG II entry in the old phone's Bluetooth settings.
  2. On MG II, hold the EQ button for three seconds to start Bluetooth re-pairing, as stated in the official manual.
  3. Open Bluetooth settings on the phone you want to use, then select MG II again.

Common mistakes to check

  • MG II is off: hold the power button for three seconds before looking for it on your phone.
  • The wrong source is selected: use the Mode button to return to Bluetooth.
  • Another device reconnects first: disconnect it or turn its Bluetooth off, then use the three-second EQ re-pairing control.
  • MG II is not listed: switch Bluetooth off and back on in the phone settings, keep the phone close to MG II, and try the EQ re-pairing control again.

When to contact support

Contact us if MG II still does not appear or reconnect after trying the steps above. Please include the model (MG II), your phone type, the steps already tried and a short video if it helps show the issue. If your request is about an order or warranty, include your Amazon order number.

support@maddeckers.com
maddeckers@outlook.com

Download the MG II manualVisit MG II Support

Deutsch

MG II per Bluetooth koppeln oder erneut verbinden

Halten Sie die Ein/Aus-Taste drei Sekunden gedrückt, um MG II einzuschalten. Wählen Sie bei Bedarf mit der Modustaste Bluetooth und anschließend in den Bluetooth-Einstellungen des Smartphones MG II. Zum erneuten Koppeln halten Sie laut Handbuch die EQ-Taste drei Sekunden gedrückt.

  1. Schalten Sie MG II ein und wählen Sie bei Bedarf Bluetooth mit der Modustaste.
  2. Aktivieren Sie Bluetooth am Smartphone und wählen Sie MG II aus der Geräteliste. Halten Sie das Smartphone beim Koppeln in der Nähe.
  3. Bei einer erneuten Verbindung trennen Sie zuerst andere verbundene Geräte. Halten Sie dann die EQ-Taste drei Sekunden gedrückt und wählen Sie MG II erneut auf dem gewünschten Smartphone.

Wenn MG II nicht erscheint, prüfen Sie den gewählten Modus, Bluetooth am Smartphone und andere bereits verbundene Geräte. Hilfe: support@maddeckers.com oder maddeckers@outlook.com.

日本語

MG IIをBluetoothで接続・再接続する

電源ボタンを3秒長押ししてMG IIの電源を入れます。必要に応じてモードボタンでBluetoothを選択し、スマートフォンのBluetooth設定でMG IIを選びます。再ペアリングする場合は、説明書に従ってEQボタンを3秒長押しします。

  1. MG IIの電源を入れ、必要に応じてモードボタンでBluetoothを選択します。
  2. スマートフォンでBluetoothをオンにし、機器一覧からMG IIを選びます。ペアリング中はスマートフォンを本体の近くに置いてください。
  3. 再接続する場合は、先に接続されている他の機器を切断します。次にEQボタンを3秒長押しし、使用するスマートフォンでMG IIをもう一度選択します。

MG IIが表示されない場合は、モード設定、スマートフォンのBluetooth、すでに接続されている他の機器を確認してください。お問い合わせ：support@maddeckers.com ／ maddeckers@outlook.com